MR-J4-200A AC Servo Drive 220V 2KW 1-Axis New

mode name

MR-J4-200A

Stocked Item

S

Output

Rated Voltage

3-phase 170 VAC

Rated Current (A)

11.0

Main Circuit

Power

Supply

Voltage/Frequency

3-phase 200 VAC to 240 VAC, 50/60 Hz

Rated Current (A)

10.5

Permissible Voltage Fluctuation

3-phase 170 VAC to 264 VAC

Permissible Frequency Fluctuation

±5% maximum

Control

Circuit

Power

Supply

Voltage/Frequency

1-phase 200 VAC to 240 VAC, 50/60 Hz

Rated Current (A)

0.2

Permissible Voltage Fluctuation

1-phase 170 VAC to 264 VAC

Permissible Frequency Fluctuation

±5% maximum

Power Consumption (W)

30

Interface Power Supply

24 VDC ±10% (required current capacity: 0.5 A (including CN8 connector signal))

Load-Side Encoder Interface

Mitsubishi high-speed serial communication

Tolerable Regenerative Power of the Built-in

Regenerative Resistor(W)

100

Control Method

Sine-wave PWM control/current control method

Dynamic Brake

Built-in

Protective Functions

Overcurrent shut-off, regenerative overvoltage shut-off, overload shut-off (electronic thermal), servo motor overheat protection,encoder error protection, regenerative error protection, undervoltage protection, instantaneous power failure protection, over-speed protection, error excessive protection, magnetic pole detection protection, linear servo control fault protection

Position

Control

Mode

Maximum Input Pulse Frequency

4 Mpps (when using differential receiver), 200 kpps (when using open-collector)

Positioning Feedback Pulse

Encoder resolution: 22 bits

Command Pulse Multiplying Factor

Electronic gear A/B multiple, A: 1 to 16777216, B: 1 to 16777216, 1/10 < A/B < 4000

Positioning Complete Width Setting

0 pulse to ±65535 pulses (command pulse unit)

Error Excessive

±3 rotations

Torque Limit

Set by parameters or external analog input (0 V DC to +10 V DC/maximum torque)

Speed

Control

Mode

Speed Control Range

Analog speed command 1:2000, internal speed command 1:5000

Analog Speed Command Input

0 V DC to ±10 V DC/rated speed (Speed at 10 V is changeable with

Speed Fluctuation Rate

±0.01% maximum (load fluctuation 0% to 100%), 0% (power fluctuation: ±10%)

±0.2%maximum(ambient temperature 25 ± 10 centigrade degree) only when using analog speed command

Torque Limit

Set by parameters or external analog input (0V DC to +10 VDC/maximum torque)

Torque

Control

Mode

Analog Torque Command Input

0VDCto±8VDC/maximum torque (input impedance: 10 to 12 kohm)

Speed Limit

Set by parameters or external analog input (0VDC to ± 10 VDC/rated speed)

Fully Closed Loop Control

Available in the future

Safety Function

STO (IEC/EN 61800-5-2)

Communication Function

USB: Connect a personal computer (MR Configurator2 compatible)

Structure (IP Rating)

Force cooling, open (IP20)

Close Mounting

Possible

Weight (kg)

2.1

MR-J4-10A

MR-J4-60A AC Servo Drive 220V 600W 1-Axis New

MR-J4-20A

MR-J4-20A AC Servo Drive 220V 200W 1-Axis New

MR-J4-40A

MR-J4-40A AC Servo Drive 220V 400W 1-Axis New

MR-J4-60A

MR-J4-60A AC Servo Drive 220V 600W 1-Axis New

MR-J4-70A

MR-J4-70A AC Servo Drive 220V 750W 1-Axis New

MR-J4-100A

MR-J4-100A AC Servo Drive 220V 1KW 1-Axis New

MR-J4-200A

MR-J4-200A AC Servo Drive 220V 2KW 1-Axis New

MR-J4-350A

MR-J4-350A AC Servo Drive 220V 3.5KW 1-Axis New

MR-J4-500A

MR-J4-500A AC Servo Drive 220V 5KW 1-Axis New

MR-J4-700A

MR-J4-700A AC Servo Drive 220V 7KW 1-Axis New