CNC 4.5KW Engraving Air Cooled 18000rpm Spindle System ER32 AC380V CNC Spindle Motor with VFD Controller

item ID#: GDZ120*103-4.5+E550-4t0055L
  • Item condition: New and Original
  • 9 available/ 1 sold
  • Start from: 1 Unit(s)
  • Weight: 22 Kg(s)
  • Manufactured by: Made in China
  • DHL Recommended Shipping
  • Stock Lead Time
Delivery:
3-7 Days Details
Payment:
Details
Guarantee:
1Year Quality Assurance Details
Returns:
7 days unconditional return, the buyer bear the return freight Details

Estimate Shipping Costs

Quantity: Unit(s)
US$815.00 + Shipping Cost
    • Description
    • Download
    • Product Reviews
    • Write a Review

    the expert of cnc parts(45).jpg

    CNC 4.5KW Engraving Air Cooled 18000RPM Spindle System  ER32 AC380V  CNC Spindle Motor with VFD Controller


    Package Content:

    1 x 4.5KW Spindle Motor

    1 x 5.5KW VFD Variable Frequency Driver

    Spindle Motor Specification:

    Providing the default Collet ER32 12.7mm, if not please do contact us for a better solution.

    Model

    GDZ120*103-4.5

    Product type

    Square High-Speed Motorized Spindle Motor for Woodworking

    Brand

    Changsheng(Made in China)

    Speed

    18000rpm

    Power

    4.5KW

    Voltage

    220V

    Current

    17.3A

    Frequency

    300Hz

    Collet

    ER32 12.7mm default

    Lubrication

    Grease

    Cooling type

    Air cooling

    Bearings

    2x7008c P4  +  2x7004c P4

    VFD Specification:

    Model

    E550-2S0055L

    Power (KW)

    5.5KW

    Input Voltage(V)

    1-phase AC 220V ±20% 50/60Hz

    Output Voltage(V)

    0~220V

    Output Current(A)

    24A

    Output Frequency (Hz)

    0~1000Hz

    Origin& Warranty&brand

    China & One year&sunfar

    1. Electric spindle practices

    Electric spindle is a high-speed high-precision components rigidity, we must strictly follow the practices used spindle spindle motor, otherwise it will increase equipment failures, shorten equipment life. Please use the rule as follows:

     (1) Before the boot, first ensure that the spindle cooling system to work properly, and then turn the power spindle. Do not use the spindle without the cooling conditions, it is necessary to check the fan and pump are working properly before use. If the spindle is water cooled, to check whether the cooling water containing impurities to ensure water is smooth.

    (2) When using electric spindle, spindle from low according to the principle of high speed, gradually increasing speed to warm up, when the spindle load up to speed and smooth operation of the state after the required processing, can better protection spindle, to reduce the wear.

    (3) during use is strictly prohibited beat, hit threaded spindle clamp and rotor end, so as not to reduce the component life, affect the results spindles used.

    (4) During the operation, the tool must be replaced in the correct way. When the knife, the focus should be uniform, the tool should be aligned with the threaded end of the screw rotor, clamping can be. During operation the tool needs to be replaced before the replacement to wait Spindle cooling, avoid tool change at hot temperature state.

    (5) During the operation, if the fixture card spindle rotor end, non-beat way to remove Jigs. Only under the premise of no damage to the rotor shaft threads with pliers and other tools to remove the chuck, and clean the rotor tapered bore and clamp the spindle to avoid Movies shorten life, affecting the quality of workpiece. If the fixture has completely lost precision, it must be replaced immediately.

    2. The spindle maintenance specification:

     (1) to control the spindle actual time worked. Theoretically prohibit spindle 24 hours of continuous work, operating 12 hours per spindle Spindle let rest at least 2 hours, in order to prevent the formation of shortened due to mechanical fatigue life of the spindle.

     (2) to understand the conditions, the ambient temperature and the spindle temperature control. Spindle operating ambient temperature not higher than 35 centigrade degree, when the ambient temperature is above 35 centigrade degree should use air conditioners or other protective measures to reduce the room temperature, thereby reducing spindle temperature.

     (3) The spindle cooling water must be kept clean and free of impurities, recommendations to clean up after the end of the spindle shaft waterway, scale and water holes to avoid clogging due to rust. Also, always pay attention to circulating water temperature in the tank, so the water temperature is too high, the cooling effect can not be achieved prefetching.

    (4) Always check the power supply connector, to avoid damage to the connector loose or aging brings to the spindle and the drive.

    (5) If the downtime to use again, you must tranches from low speed to high speed spindle run-in steps according to the spindle load running, in order to use in the run-through.

    (6) during the loading and unloading cutter knife, must tool chuck nut clean.

    3. Use Caution

    (1) must match the drive spindle chosen correctly according to the electric spindle nameplate good debugging power, voltage and frequency.

    (2) Set the frequency converter should be set command channel, and then set the display channel, and finally set the parameters. When setting parameters, be sure that the reference frequency, the frequency of the three highest rated frequency and consistency.

    (3) The spindle is generally clockwise in the wrong direction, the drive can change settings or swap any two rotating wire the inverter output UVW terminal on.

    (4) In general, water-cooled spindle surface temperature and ambient temperature greater than 20 degrees, the heat can be considered a spindle; when air-cooled spindle surface temperature greater than ambient temperature of 30 degrees, can be identified as the main heat seriously, immediately shut down cooling, a check

    4. Maintenance Caution

    (1) Spindle found abnormal sound, should immediately stop checking. If you can not be resolved, should be sent to the manufacturer or repair to professionals.

    (2) the operation of an abnormal burning smell, immediately stop checking. If you can not be resolved, should be sent to the manufacturer or repair to professionals.

    (3) If the spindle does not run the boot, do not start over, you should carefully check the following related matters: first check the drive parameters to determine the input and output voltage, the spindle parameter settings are correct. Second, check the power cord and wiring connector is plugged in and determine whether the contact connector problem.

    (4) Since the electric spindle is a high speed, high rigidity precision components and must therefore be sent back to me by professionals or for repair.

     

    Shipment:

    1. Usually we will ship the items within 3 working days after the payment is reached.
    2. DHL, UPS, Fedex, or EMS is available for shipping.
    3. Delivery time:DHL, UPS, Fedex, EMS express shipping usually take 3-10 working days depends on the country delivered to.
    4. Please check out your ADDRESS carefully when processing order.
    5. Buyers please note: Accessories tariffs must be buyers to pay.The buyer can choose EMS express to avoid tariffs.
    6. Any accidents, delays or other issues are the responsibility of the shipping service.

    We promise to:

        Offer our customers the low Chinese price.
        Streamline the buying and paying process.
        Deliver goods to our customers all over the world with speed and precision.
        Ensure the excellent quality of our products.
        Help you find products and manufacturers in China.

    Return Policy:

        We accept 14 days return policy. If you want to return the item, please contact us in 14 days first and make sure the package is un-opened. The buyer has to pay for the go and back delivery cost and the custom fee of each country. Once we received the product and checked, we will make refund for the part in 24 hours.
        Any quality problem in normal use during the warranty period, we will repair for free. The buyer should pay the return cost and our company will pay the re-shipping cost.

     

    company(192).png

    There are currently no product reviews.

    Tell us what you think about this item, share your opinion with other people. Please make sure that your review focus on this item. All the reviews are moderated and will be reviewed within two business days. Inappropriate reviews will not be posted.

    Have any question or inquire for this item? Please contact us. Our customer representative will get back shortly.

    Indicates required fields*
    Rating: *
    Your Name: *
    Your Email: *
    Review Title: *